It’s difficult to surprise an experienced audiophile. We’ve gone to all the trades shows, purchased and borrowed lots of gear, and visited all our local dealers. We’ve essentially heard all the possible sonic varieties and tradeoffs. But every so often…a product comes along that challenges your preconceptions.
A few months back, one such product for me was the ZenWave Audio PSR-14 power cable. It was awarded “Best in Class” not only because it outperformed much pricier cables on many aspects – but because it had both technicality and musicality. Which is a unicorn of a combination. The only tradeoff I could hear was the less organic and more neutral tone. Which, admittedly, may not be a tradeoff depending on who you ask.
I was so impressed by its performance, I asked ZenWave Audio if they could make a UPOCC copper version, not just for a power cable, but a speaker cable as well. Although ZenWave is pretty tight-lipped about what their ribbon conductor design entails (for good reason), you could find a few hints here.
The SCR and SSR (Speaker cable, Copper Ribbon speaker cable, Silver Ribbon, respectively) speaker cables are derived from the PSR-14 power cable (Power cable, Silver Ribbon – 14 gauge), and are available in both 14 and 11 gauge versions, which would be the SCR-14 and SCR-11 or SSR-14 and SSR-11. The PSR-14 is a cost-no-object UPOCC silver power cable using a fairly advanced ribbon conductor design that allows me to make the cable with less inductance vs a conventional cable. This worked so well that I used it as a basis to make other cables, I made copper ribbon power cables as well as the silver and copper ribbon speaker cables.
The speaker cables are very similar to the power cables, but have more balanced inductance vs capacitance, the speaker cables have less capacitance vs the power cables. I also use the ribbon conductors to make interconnect cables, the DSR IC is a 17g UPOCC silver IC cable and there will be copper versions eventually as well. The ICs have far less capacitance vs the power and speaker cables, so a totally different geometry, these cables will offer alternatives to my silver/gold alloy and copper litz interconnect cables.
Fortunately, a few months later I received the ZenWave Audio speaker cables with both copper and silver variants (SCR-14 and SSR-14 respectively). My focus will be one the copper variant: the ZenWave Audio SCR-14. Let’s get started.
As far as build quality, the speaker cables have a layer of pure, unbleached cotton under the techflex, and the colors of techflex are “carbon” and “dark carbon.” The dark carbon has a black layer under it while the carbon has white underneath. The cables themselves are very flexible and the Furutech banana connectors twist on securely.
Admittedly, the aesthetics are closer to a DIY cable. It feels more handmade and “fabric-like.” Heck, I think these are one of very few cables I’ve ever seen with handwritten labels (which isn’t a bad thing?). So if you’re expecting carbon fiber filters with laser-etched labels – you won’t find that here. Nevertheless, a cable crafted with love.
What’s interesting is that the SSR-14 speaker cables had a very similar impact on the “big picture” as the PSR-14 power cord. It was full-bodied, resolving, and 100% transparent. Perhaps even more so in speaker cable form. In short, if you prioritize neutrality, speed, and resolution – you’ll love this cable. It still amazes me how it’s able to juggle so many sonic qualities – so damn well.
Please take a look at my review of the PSR-14 for an idea of what I mean. As with the SSR-14, I feel the tonal wasn’t as natural for vocal recordings. Never fear, that’s where the SCR-14 comes in.
This cable has most of the qualities of the SSR-14 but, in my opinion, with better tonal balance. It’s not as quick, micro-detailed, or enveloping – but it has a more colorful palette. Aside from the Danacabel Sapphire Mk.2, I don’t think I’ve heard a speaker cable that reproduces timbre so accurately. Generally, speaker cables with accurate tonality have more roughness, are thinner sounding, and at times a bit wiry. I figured this was the “expected” tradeoff, but ZenWave Audio has now removed that notion with their new ribbon conductors.
Let’s break down what you’re getting with this speaker cable. The ZenWave SCR-14’s three major strengths are timbre, material resolution, and cohesion.
I went through my whole library of music. From hip-hop to rock, folk, classical, and electronic – and I found it very difficult to find any major faults with the SCR-14. However, when I compared it to the Furutech DPS-4 and High Fidelity Cables CT-2 speaker cables (and a few others) – I did start to notice a few tradeoffs.
First, the SCR-14 didn’t have as much bottom grunt and weight. It misses that deeper, denser presence. In other words, it doesn’t thump or flex as outwardly in the bass region as prominently. This is especially noticeable in the lower octaves of piano notes. Keep in mind, these are the relative differences. The SCR-14 is not thin sounding at all. And, for what it’s worth, the SCR-14 still sounds more like a piano.
OK, so the tradeoff for the aforementioned qualities is a leaner bottom end. Fortunately, this was easy to mitigate with the thicker sounding amplifier such as the Emerald Physics 100.2SE. Timbre takes a slight hit – but you get a heavier and more gravitational sound. The amazing thing is that the SCR-14 still preserves fullness while maintaining the lowest levels of nuance. It doesn’t overdo it – just enough of it. So far, I feel the tradeoff is absolutely worth getting better tonal quality.
Alternatively, ZenWave Audio offers an 11-gauge version of this cable: the SCR-11. Depending on your amplifier and speakers, this may actually add more body to the sound without any compromises to timbre. I’ll hopefully get a demo cable end soon.
ZenWave Audio has made great cables in the past – but they knocked it out of the park with these UPOCC ribbon cables. They are progressively different (in a good way) from any speaker cable I’ve heard so far.
As far as the variants, some may prefer the SSR-14 for its neutrality, soundstage, transient clarity, and the utmost amount of transparency. But for my tastes, the SCR-14 is more captivating, pure, and has more “intent.” Not to mention its timbral accuracy is pretty much second to none. Oh yeah, it’s also much more affordable.
The recurring themes with the ZenWave Audio SCR-14 speaker cables are “truth” and “passthrough.” There’s a unique quality that’s not a ‘special effect” but one of unimpeded transparency in both resolution and tone. There’s always ease to the sound yet it remains powerful and unimpeded. The ZenWave SCR-14 has not only given me fresh insight into new and old recordings – but newfound hope for innovation in this space.
Needless to say, the ZenWave Audio SCR-14 is in the running for Product of 2020. But is it a giant killer? At its level of performance and price point – it sure seems like it.
Below are prices for a stereo pair without connectors. The Furutech FT-211 and FT-212 connectors are an additional $300. The product page will be up soon. Please contact ZenWave Audio for a quote.
|SCR-14 – UPOCC Copper Ribbon|
|1m pair||Per Meter|
|SSR-14 – UPOCC Silver Ribbon|
|1m pair||Per Meter|
SAN FRANCISCO, April 7, 2021 -- THX Ltd., a world-class audio and video certification and technology… Read More
I'll be comparing the original Sennheiser Momentum True Wireless to their latest release - the… Read More